<html>
<P>Hey Sean;</P>
<P>Thanks for the quick reply.<BR>
I've configured the card in zapata.conf like this:<BR>
signalling=fxs_ks<BR>
context=incoming<BR>
channel => 1<BR>
I did install the "make sample" after asterisk was installed.</P>
<P>I started asterisk with -vvvvv. Couldn't see any obvious errors. The last few lines read:</P>
<P> == Registered custom function URIDECODE<BR>
== Registered custom function URIENCODE<BR>
== Manager registered action DBGet<BR>
== Manager registered action DBPut<BR>
== Parsing '/etc/asterisk/enum.conf': Found<BR>
Asterisk Ready.</P>
<P>Any other ideas?</P>
<P>Signed; fusterated newbie...<BR>
<BR>
<B>On Sun Feb 19 18:33 , Sean Walberg <sean@ertw.com> sent:<BR>
<BR>
</P></B>
<BLOCKQUOTE style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #5167c6 2px solid; MARGIN-RIGHT: 0px"><FONT color=red>> I've installed Debian Sarge</FONT><BR>
<BR>
My condolences.<BR>
<BR>
<FONT color=red>> running. Zttools sees my fxo card (modem with ambient chip) but when I try</FONT><BR>
<FONT color=red>> calling the PBX does not answer.</FONT><BR>
<BR>
Did you configure the fxo card in /etc/asterisk/zapata.conf? This tells<BR>
<BR>
<FONT color=red>> I have not configured a dialplan yet, is that required? I'm kind of assuming</FONT><BR>
<FONT color=red>> out of the box the pbx would pick up.</FONT><BR>
<BR>
Yes, you'll need something to Answer() the call, implicitly or<BR>
explicitly. Even the demo from "make sample" should do the trick.<BR>
<BR>
Also start up asterisk with -vvvvv and watch the console. <BR>
<BR>
Sean<BR>
<BR>
<FONT color=red>> -----Original Message-----</FONT><BR>
<FONT color=red>> From: <A href="javascript:top.opencompose('asterisk-bounces@muug.mb.ca','','','')">asterisk-bounces@muug.mb.ca</A> [<A href="javascript:top.opencompose('<a href=" javascript:top.opencompose(?asterisk-bounces@muug.mb.ca?,??,??,??)?>asterisk-bounces@muug.mb.ca</A>','','','')"><A href="javascript:top.opencompose('asterisk-bounces@muug.mb.ca','','','')">asterisk-bounces@muug.mb.ca</A></A>] On</FONT><BR>
<FONT color=red>> Behalf Of Sean Walberg</FONT><BR>
<FONT color=red>> Sent: Saturday, February 18, 2006 10:17 AM</FONT><BR>
<FONT color=red>> To: Asterisk Open Source PBX SIG</FONT><BR>
<FONT color=red>> Subject: Re: [*] New Asterisk Install</FONT><BR>
<FONT color=red>> </FONT><BR>
<FONT color=red>> On Sat, 2006-02-18 at 10:15 -0600, Sean Walberg wrote:</FONT><BR>
<FONT color=red>> > Try "debug sip" in the asterisk cli and see if it reports anything when</FONT><BR>
<FONT color=red>> </FONT><BR>
<FONT color=red>> And of course, I mean "sip debug". Asterisk != IOS :)</FONT><BR>
<FONT color=red>> </FONT><BR>
<FONT color=red>> Sean</FONT><BR>
<FONT color=red>> </FONT><BR>
-- <BR>
Sean Walberg <<A href="javascript:top.opencompose('sean@ertw.com','','','')">sean@ertw.com</A>> <A href="parse.pl?redirect=http%3A%2F%2Fertw.com" target=_blank><FONT color=red>http://ertw.com</FONT></A><BR>
<BR>
_______________________________________________<BR>
Asterisk mailing list<BR>
<A href="javascript:top.opencompose('Asterisk@muug.mb.ca','','','')">Asterisk@muug.mb.ca</A><BR>
<A href="parse.pl?redirect=http%3A%2F%2Fwww.muug.mb.ca%2Fmailman%2Flistinfo%2Fasterisk" target=_blank><FONT color=red>http://www.muug.mb.ca/mailman/listinfo/asterisk</FONT></A><BR>
</BLOCKQUOTE>
</html><BR>